Total permissible floor area = plot area × FAR. Storeys ≈ total floor area ÷ the area of each floor.
In the RAJUK area two caps apply: the area-based FAR of your DAP density block and the FAR for the width of the road in front. The lower one usually decides.
The revised DAP 2022–2035 and the Dhaka Metropolitan Building Construction Rules 2025 were gazetted in December 2025, replacing the 2008 rules. A 6 m (about 20 ft) road now carries a reported FAR of 3.25 and a 9 m (about 30 ft) road 3.5.
A DAP amendment gazetted on 14 October 2026 offers up to 0.5 extra FAR to plots of 5 katha or more in Purbachal and Jhilmil whose owners apply within six months.
Ground coverage, setbacks, the cap on flats per katha, parking, aviation height and fire rules also shape the building.
Confirm your plot's figures with the gazetted DAP, a RAJUK land use clearance and an architect's feasibility check before you buy land or sign with a developer.
What is FAR (floor area ratio)?
FAR is the total floor area of a building divided by the area of its plot. The 2008 Dhaka building rules defined it this way with two refinements that still matter: spaces the rules exempt are left out of the floor area, and land given up for a road is left out of the plot area.
A FAR of 2.0 means your counted floor area can be twice your land area. It does not tell you the number of storeys: the same FAR can produce a low, wide building or a taller, slimmer one.
The basic RAJUK FAR calculation formula
Permissible floor area = net plot area × permitted FAR
Floor plate = net plot area × the ground coverage you use (within coverage and setback limits)
Approximate number of storeys = permissible floor area ÷ floor plate
In Dhaka, 1 katha is 720 sq ft (about 1.65 decimal), so 3 katha = 2,160 sq ft and 5 katha = 3,600 sq ft (about 334 sq m). Check your deed area against a fresh survey; plots are rarely exact.
How FAR rules in Dhaka work today: DAP 2022–2035 FAR and the revised DAP
Across the roughly 1,528 sq km the Detailed Area Plan covers, two documents decide what you may build: the DAP fixes land use and density, and the building rules turn those limits into drawings. The DAP 2022–2035 was gazetted on 24 August 2022, amended in September 2023 and revised in December 2025.
Area-based FAR (your DAP density block)
The DAP divides the city into population density blocks, each with its own maximum FAR. The 2025 revision merged the earlier 275 blocks into 68 and raised the maximum density figure, according to The Business Standard. Your block's FAR is a ceiling, however wide your road.
Your plot also gets a FAR based on the width of the road it faces, because wider roads can carry more traffic, services and fire engines. Prothom Alo reports that the December 2025 revision raised the FAR for a plot on a 6 m (about 20 ft) road from 2.75 to 3.25, and on a 9 m (about 30 ft) road from 3.25 to 3.5. Narrower lanes earn less.
Which FAR applies: the lower one usually controls
In a 2024 example from Mohammadpur, Prothom Alo reported a road-based FAR of 2.75 beside a 20 ft road but an area-based FAR of 2.3, so a 5 katha plot was limited to 8,280 sq ft (2.3 × 3,600). After the 2025 revision, the same paper reported that a 5 katha plot on a 20 ft road in Mohammadpur, Old Dhaka or Gulshan-Banani could reach 11,700 sq ft, which is the road-based 3.25. In each case the lower figure set the limit.
When the revision was approved in October 2025, The Business Standard reported a bonus of 0.25 to 0.75 FAR for block-based developments that merge plots, and incentives for green buildings in the draft rules. Every incentive has conditions, so check which ones your plot can realistically claim before you count on them.
What changed in the revised DAP, and what is new in 2026
The 2025 revision raised FAR across most of the RAJUK area. At the approval stage in October 2025, The Business Standard listed examples such as Mirpur (2.8 to 3.4), Mohammadpur (2.7 to 3.4), Old Dhaka (2.6 to 3.3), Khilgaon (2 to 3.4) and Savar (2 to 3.4). Treat these as reported figures, not your plot's final value.
The gazette followed in December 2025, together with the Dhaka Metropolitan Building Construction Rules 2025, which replaced the 2008 rules. Prothom Alo reported that area FAR rose in places including Old Dhaka, Mogbazar, Shewrapara, Mohammadpur, Panthapath, Mirpur, Badda, Niketan and Baridhara; fell in Dhanmondi, Gulshan, Banani and Satarkul; and stayed the same in areas such as Bashundhara Residential Area and Jolshiri.
The cap on flats changed too. In Old Dhaka it rose from 1.2 to 2.4 units per katha, so a 5 katha plot there can now hold up to 12 flats.
The October 2026 amendment
On 14 October 2026 the housing ministry gazetted a third round of DAP changes. Owners of residential plots of 5 katha or more in Purbachal and Jhilmil can get up to 0.5 extra FAR if they apply for plan approval within six months from 15 October 2026 and build to plinth level within a year of approval, or pay a penalty of 20 times the approval fee. The Daily Star reported that road width, setback, ground coverage and height rules were unchanged. Planners have demanded the amendment be withdrawn, so check its status before relying on it.
The 2008 Dhaka building construction rules: where the FAR system started
Most buildings you see in Dhaka today were approved under the Dhaka Mohanagar Imarat (Nirman, Unnayan, Sangrakshan o Aposaran) Bidhimala 2008. It set FAR and maximum ground coverage (MGC) by plot size, road width and building type, with no area-based cap.
Under its residential table, a plot of 4 to 5 katha on a 6 m road had a FAR of 3.50 and an MGC of 62.5%. On 5 katha that meant about 12,600 sq ft on a footprint of up to 2,250 sq ft, or roughly five and a half typical floors. The DAP 2022 then added the area-based cap and building area fell in many neighbourhoods. Use the 2008 tables only to understand older buildings, not to plan a new one.
Ground coverage (MGC), setbacks and open space
Ground coverage is the share of the plot your building covers; setbacks are the gaps you leave at the front, back and sides. Together they fix the size of each floor and therefore, for a given FAR, the number of storeys.
RAJUK's own example, reported by The Business Standard: at a FAR of 2.5, a building that keeps only the minimum open space rises four to five storeys, while one that leaves more open space can rise seven to eight storeys. More open ground buys you height.
Setback rules in Dhaka: what to expect
The 2008 rules give a sense of scale. For buildings up to 10 storeys on plots of 4 to 20 katha, minimum setbacks were 1.5 m at the front, 2 m at the back and 1.25 m on each side; taller buildings needed 3 m at the back and sides. No building could stand closer than 4.5 m to the centre of the existing road, which bites hard on narrow lanes. The 2025 rules revise these provisions and tighten enforcement, so your architect must use the current tables, not the building next door.
Open space you cannot pave over
The 2008 rules required at least half of the mandatory open space to stay unpaved so rainwater could soak in, and basements could not extend beneath that half. Check how the current rules treat open space before you plan driveways, ramps and basements.
RAJUK FAR calculation for 3 katha and 5 katha: worked examples
These examples are illustrative. They use round numbers to show the method and are not approved figures for any particular plot.
Example 1: How many floors can I build on 5 katha on a 20 ft road?
Plot: 5 katha = 3,600 sq ft
Illustrative FAR: 3.25 (the reported road-based FAR for a 6 m road, assuming a higher area FAR)
Permissible floor area: 3,600 × 3.25 = 11,700 sq ft
Floors covering 60% of the plot (2,160 sq ft): 11,700 ÷ 2,160 = 5.4, so about 5 full floors
Floors covering 50% (1,800 sq ft): 11,700 ÷ 1,800 = 6.5, so about 6 full floors
Floors covering 40% (1,440 sq ft): 11,700 ÷ 1,440 = 8.1, so about 8 floors
The total floor area stays the same; only the shape changes, and with it the lift, structure and cost per sq ft. Our construction cost guide shows how to budget each option.
Example 2: How many floors can I build on 3 katha with a FAR of 2.5?
Plot: 3 katha = 2,160 sq ft
Permissible floor area: 2,160 × 2.5 = 5,400 sq ft
At 60% coverage (1,296 sq ft per floor): about 4 floors
At 35% coverage (756 sq ft per floor): about 7 small floors
On small plots the stair, lift and columns take a large share of each floor, so aim for a usable plan, not the tallest possible building.
Example 3: How many flats?
The DAP also caps dwelling units per katha. At the Old Dhaka figure of 2.4 units per katha, a 5 katha plot allows 12 flats, or about 975 sq ft of floor area each before common areas are deducted. Where the cap is lower, you get fewer, larger flats.
Want to know exactly how many floors your plot can take? Send us the deed, survey and road width: call +880 1823-017070, email sthapatto@gmail.com or start your project online.
Parking, basements and what counts toward FAR
What you count matters as much as the FAR. The 2008 rules left several spaces out of the FAR calculation, including:
Parking up to twice the minimum number of spaces, with driveways, ramps and car lifts
A compulsory fire stair (not a building's only stair), the stair top and the lift machine room within size limits
Substation, generator, meter and air-conditioning plant rooms, water tanks, open terraces and small hanging balconies
The same rules counted mezzanines in full and added extra area for floors taller than 4.25 m. When the parking floor is excluded, the floors you calculate from FAR sit above it.
The 2008 rules set minimum parking by flat size: one car space per flat above 200 sq m, two per three flats of 140 to 200 sq m, one per two flats of 90 to 140 sq m, one per four flats of 60 to 90 sq m, and one per eight flats up to 60 sq m. If the cars do not fit, you cannot use all of your FAR.
Under the 2008 rules, a basement could extend under up to half of the mandatory open space and to the boundary wall where the neighbour's safety was secured, but had to keep the road-side setback. Basements need careful soil investigation, so price them early; see our soil test guide.
What is new under the 2025 rules
Plots of 5 katha or more must now include a sewage treatment plant (STP). Approval also needs architectural, structural, electrical, mechanical and plumbing drawings, plus fire safety drawings. Because the 2025 rules replaced the 2008 exemptions, ask your architect how parking, stairs and service rooms are counted now.
Height and storeys: limits beyond FAR
Aviation: near flight paths you need a Civil Aviation Authority no-objection certificate, which can cap height.
Fire safety: buildings above 10 storeys need a Fire Service NOC.
Building code: BNBC 2020 classes a building of 10 storeys or 33 m and above as multi-storey, which brings additional requirements.
Access: a tall building on a narrow lane may not be able to provide the parking or fire access it needs.
RAJUK FAR calculation step by step: how to check your own plot
Collect the plot details: mouza, dag (plot) number, khatian, deed area and a recent survey.
Locate the plot on the gazetted DAP map to find its land use zone and density block. RAJUK publishes its laws, rules and notices at rajuk.gov.bd.
Measure the road in front at several points, and ask how any planned widening will be treated.
Apply to RAJUK for land use clearance or planning approval, the first stage, which confirms the use permitted on the plot.
Ask an architect for a feasibility study covering area FAR, road FAR, incentives, the unit cap, coverage, setbacks, parking, STP and height, with a massing sketch of realistic floors.
Only then fix the land price, sign a developer agreement or start detailed design.
Budget for fees too: Prothom Alo and Bonik Barta report residential approval fees under the 2025 rules of Tk 50 per sq m, so 11,700 sq ft (about 1,087 sq m) comes to roughly Tk 54,000, plus a Tk 5,000 application fee. Confirm the schedule when you apply. Our building approval guide for Dhaka explains the steps that follow.
Common FAR mistakes landowners make
Buying a plot on a narrow road. A cheaper plot on a narrow lane can carry far less floor area than one on a 20 ft road.
Assuming your neighbour's height applies to you. That building may have been approved under the 2008 rules or a wider road, or not approved for its present height at all.
Using the deed area instead of the net area. Land for road widening, and area your survey cannot confirm, does not count.
Forgetting the cap on flats, which decides how many units you can sell or rent.
Designing to the full FAR without drawing parking, setbacks and the STP. Doing that properly can cost you a floor.
Trusting a verbal promise of "ten storeys" from a broker or developer. Ask for the calculation behind every number.
Building beyond the approved plan. It is an offence under RAJUK law, punishable by fines and imprisonment.
Outside Dhaka: CDA, KDA, RDA and pourashava rules
Everything above applies to the RAJUK area. In Chattogram the Chittagong Development Authority approves buildings; in Khulna and Rajshahi, the KDA and RDA; elsewhere, the city corporation or pourashava; inside export processing and economic zones, the zone authority. Each has its own plans, rules and fees, so your FAR and height will differ from Dhaka.
The Bangladesh National Building Code 2020, however, applies across the country, so a plot in Feni, Gaibandha or a village still needs a design that meets BNBC. Read our village house design guide for rural plots.
How Sthapatto Angon can help
A FAR check is the first thing we do for a new plot. Our architects read the gazetted DAP and current rules for your site, test several massing options and show you the trade-offs between height, floor size, flat count, parking and cost. Our structural and MEP engineers then design to BNBC 2020, and we prepare the drawing set the 2025 rules require.
Plot feasibility and FAR study before you buy or sign with a developer
Architectural, structural and MEP design in-house, including STP and fire safety design
Approval drawings and coordination with RAJUK or the local authority
Project management consultancy and construction services for buildings we design
Our residential work in the RAJUK area includes nine-storey residential buildings at Jolshiri Abashon (one completed in 2023, others approved or under construction), a seven-storey residential building at Bashundhara R/A (completed 2015) and the nine-storey Jalalabad residence in Banani (completed 2015). See our residential projects and house and apartment building design service.
Frequently asked questions
How do I calculate FAR for my plot in Dhaka?
Multiply the net plot area by the permitted FAR to get the total floor area you may build. In the RAJUK area the permitted FAR is generally the lower of your DAP block's area FAR and the FAR for your road width, plus any incentive you qualify for. Then check coverage, setbacks, parking and the unit cap.
How many floors can I build on 5 katha land in Dhaka?
It depends on your FAR and how much of the plot each floor covers. As an illustration, a FAR of 3.25 gives 11,700 sq ft: about 5 floors at 60% coverage or about 8 floors at 40%. Your real answer needs the gazetted figures for your plot.
How many floors can I build on 3 katha?
With an illustrative FAR of 2.5, a 3 katha plot allows 5,400 sq ft: about 4 floors at 60% coverage or about 7 small floors at 35%. Because stairs and structure take a large share of small floors, the practical design is often lower than the maximum.
What is the FAR for a 20 feet road in Dhaka?
Prothom Alo reported that the December 2025 revision set the road-based FAR at 3.25 for a 6 m (about 20 ft) road and 3.5 for a 9 m (about 30 ft) road. If your DAP block's area FAR is lower, the lower figure applies.
Is there a RAJUK FAR chart I can use?
The values sit in the gazetted DAP and the 2025 building rules, by density block and road width. Charts online often mix 2008, 2022 and 2025 figures, so treat them as a guide and have an architect confirm your plot's values.
Is the revised DAP gazetted?
Yes. The revised DAP and the Dhaka Metropolitan Building Construction Rules 2025 were gazetted in December 2025. A further amendment covering Purbachal, Jhilmil and some land use changes was gazetted on 14 October 2026.
Does ground-floor parking count in FAR?
Under the 2008 rules, parking within set limits, including driveways and ramps, was excluded from FAR. The 2025 rules replaced those provisions, so confirm how your architect is counting parking now.
What are the plan pass rules in Dhaka in 2026?
Under the 2025 rules, approval runs in stages: planning approval, then construction approval with architectural, structural, electrical, mechanical, plumbing and fire safety drawings, then an occupancy certificate. Plots of 5 katha or more must include an STP.
ফার (FAR) বা ফ্লোর এরিয়া রেশিও দিয়ে বোঝা যায় আপনার জমিতে মোট কত বর্গফুট ফ্লোর বানানো যাবে। হিসাবটি সহজ: জমির আয়তন × ফার = মোট অনুমোদনযোগ্য ফ্লোর এরিয়া। যেমন ৫ কাঠা (৩,৬০০ বর্গফুট) জমিতে ফার ৩.২৫ হলে মোট প্রায় ১১,৭০০ বর্গফুট। প্রতি তলায় জমির কতটুকু ঢাকবেন, তার ওপর তলার সংখ্যা নির্ভর করে; বেশি খোলা জায়গা রাখলে একই ফারে ভবন উঁচু করা যায়। রাজউক এলাকায় ড্যাপের এলাকাভিত্তিক ফার আর সামনের রাস্তার প্রশস্ততাভিত্তিক ফার, এই দুটির মধ্যে সাধারণত যেটি কম সেটিই প্রযোজ্য হয়। ২০২৫ সালের ডিসেম্বরে সংশোধিত ড্যাপ ও ঢাকা মহানগর ইমারত নির্মাণ বিধিমালা ২০২৫ গেজেট আকারে প্রকাশিত হয়েছে। প্রতিবেদন অনুযায়ী ২০ ফুট রাস্তায় ফার এখন ৩.২৫ এবং ৩০ ফুট রাস্তায় ৩.৫। পাঁচ কাঠা বা তার বড় প্লটে এসটিপি বাধ্যতামূলক। জমি কেনা বা ডেভেলপারের সঙ্গে চুক্তির আগে ড্যাপ ম্যাপ, ভূমি ব্যবহার ছাড়পত্র এবং স্থপতির সম্ভাব্যতা যাচাই করে নিন। আপনার প্লটে কত তলা করা যাবে জানতে ফোন করুন ০১৮২৩-০১৭০৭০।
Ready to find out what your plot can hold?
Bring us your deed, survey and a photo of the road, and our architects will check what the current rules allow and how to use it well. Call +880 1823-017070, email sthapatto@gmail.com or start your project online.
This article is general information, not legal advice. FAR, DAP and building rule values change and differ from plot to plot; confirm the current requirements with RAJUK or your local authority and a qualified architect before you buy land, sign a developer agreement or apply for approval.